INCLUDES: PPA & 6 PAD ENGINE DISC FLYWHEEL STEP: 2.200" - 2.210"
FLYWHEEL STEP: 2.200" - 2.210"
NEW LUK, FLYWHEEL STEP: 2.200"-2.210"
NEW LUK, SPRING CENTER, INTERCHANGEABLE WITH R66923
INTERCHANGEABLE WITH 328 0061 10 & 328 0061 11
NEW LUK INTERCHANGEABLE W/R66923
GREASEABLE, SELF CENTERING BEARING WITH CARRIER
BEARING WITH CAST IRON CARRIER
FLYWHEEL STEP: 2.200" - 2.210", INCLUDES: PPA, 6 PAD ENGINE DISC AND WOVEN PTO DISC, INTERCHANGEABLE WITH R55140U
INCLUDES: PPA, 6 PAD ENGINE DISC & WOVEN PTO DISC FLYWHEEL STEP: 2.200" - 2.210" INTERCHANGEABLE WITH R27706U
NEW LUK INCLUDES: WOVEN PTO DISC INTERCHANGEABLE W/R55140 & R27706 FLYWHEEL STEP 2.200" - 2.210"
INTERCHANGEABLE WITH R55140 AND 228 0023 10, INCLUDES: WOVEN PTO DISC, FLYWHEEL STEP 2.200" - 2.210", (NEW AVAILABLE)
INCLUDES: WOVEN PTO DISC, FLYWHEEL STEP 2.200" - 2.210"
INCLUDES: WOVEN PTO DISC FLYWHEEL STEP: 2.200" - 2.210" INTERCHANGEABLE WITH R27706 & 228 0023 10
INTERCHANGEABLE WITH 323 0084 10
FITS: R55140 PPA KIT INCLUDES: 3-CAST STYLE RELEASE LEVERS, 3-LEVER SPRINGS, 3-LEVER PINS, 3-PUSH PINS, 6-LEVER PIN CLIPS & 3-ROLL PINS NOTE WHEN REPLACING STAMPED STEEL LEVERS THE PTO RELEASE PIN GUIDES ON THE BACKPLATE BELOW THE LEVERS MUST BE MACHINED DOWN FROM .550" TO .080" ABOVE BACKPLATE.
FLYWHEEL STEP: .850"
NEW LUK, FLYWHEEL STEP: .850"
SIZE: 12"
NEW LUK
SIZE" 12"
FLYWHEEL STEP: .850
INCLUDES: RING GEAR FLYWHEEL ID 13.030"
142 TOOTH RING GEAR
23CM (1.38 CI) HYDRAULIC PUMP WITH KEYED SHAFT
(R97872 NEW AVAILABLE); THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT
THIS IS A 50 CM (3 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON THE MOUNTING FLANGE LEFT SIDE , A 7/8" PRESSURE PORT IN THE PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON THE BOTTOM. IT DOES NOT HAVE AN INLET PORT ON THE MOUNTING FLANGE RIGHT SIDE. NOTE: THE INDICATED SIDES OF PUMP ARE AS SEEN FROM THE TRACTOR SEAT. IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED.
THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT
23CM (1.38 CI) HYDRAULIC PUMP WITH KEYED SHAFT; (NEW AVAILABLE)
1 1/16" MALE O-RING x 7/8" MALE JIC
45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC
FITS: 0.7 C.I. (12cc) & 1.4 C.I. (23cc) PUMPS
USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R34348 SHAFT
USE WITH R34348 SHAFT AND USE WITH R45874B & R45874BR BUSHINGS Required: 2
USE WITH R79152, R79154 & R79156 SHAFTS USE WITH R80558B & R80558BR BUSHINGS Required: 2
USE WITH R39319 SHAFT Required: 2
USE WITH R79152, R79154, R79156 & R34348 SHAFTS Required: 2
USE WITH R39319 SHAFT
DIESEL INCLUDES: MOUNTING GASKET & BACKPLATE GASKET R938300 KIT AVAILABLE
FITS: R51039, R55758 & R73604 INCLUDES: 2 GASKETS, SPRING SEAL, BEARING& IMPELLER
SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS
ONE PIECE TEFLON SEAL AND WEAR SLEEVE ASSEMBLY SUB FOR AT22965, AR92893, RE11036, RE17831, RE24959