THIS ASSEMBLY IS PRESET INCLUDES: 2-R95827 ENGINE DISCS AND 2-R95827 PTO DISCS
CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED
TUBE SEAL ORING
TRANSMISSION Required: 3
PTO Required: 3
USE WITH R50152
USE WITH R39259
FITS: HI-LOW SYNCRONIZER Required: 8
USE WITH R29815 Required: QTY AS REQUIRED
FITS HI-LOW SYNCRONIZER Required: 6
USE WITH R29816 Required: QTY AS REQUIRED
(R97872 NEW AVAILABLE); THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT
THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT
1 1/16" MALE O-RING x 7/8" MALE JIC
45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC
USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R34348 SHAFT
USE WITH R34348 SHAFT AND USE WITH R45874B & R45874BR BUSHINGS Required: 2
USE WITH R79152, R79154 & R79156 SHAFTS USE WITH R80558B & R80558BR BUSHINGS Required: 2
USE WITH R79152, R79154, R79156 & R34348 SHAFTS Required: 2
GAS/DIESEL INCLUDES: BACKPLATE GASKET & MOUNTING GASKET R934030 KIT AVAILABLE
GAS/DIESEL FITS: R52009 INCLUDES: IMPELLER, SEAL, BEARING, BACKPLATE & MOUNTING GASKET
SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS
ONE PIECE TEFLON SEAL AND WEAR SLEEVE ASSEMBLY SUB FOR AT22965, AR92893, RE11036, RE17831, RE24959
3/16" X 31/64"-18 PER SET
UPDATE KIT
KIT INCLUDES: RESISTOR REPLACES ORIGINAL ASSEMBLY, FOR REPLACEMENT MOTORS ORDER BM3904
HEAVY DUTY BEARING STYLE WITH OE WIRE CONNECTORS 12V SINGLE SPEED 2 WIRE WITH 5/16" SHAFTS
OE WIRE CONNECTORS SEALED MOTOR
12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS. REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR. CAN USE HEAVY DUTY BLOWER MOTOR WITH OE CONNECTORS BM20052HD
HD BEARING STYLE WITH OE WIRE CONNECTORS & O-RINGS, 12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS. WITH OE WIRE CONNECTORS & MOUNTING O-RINGS REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR. CAN USE STANDARD VERSION BM20052
HIGH EFFICIENCY EVAPORATOR WITH HEATER CORE MUST REUSE ORIGINAL BRACKETS
AFTERMARKET
FITS ALL 30 & 40 SERIES JOHN DEERE TRACTORS, 27 PIECE KIT, SINGLE APPLICATION
CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.