JOHN DEERE 4055 John Deere Models: 3005 thru 4995

THIS ASSEMBLY IS PRESET
INCLUDES: 2-R95827 ENGINE DISCS AND 2-R95827 PTO DISCS

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

WITH BEAD SEAL & LAMINATED STEEL CENTER

WITH BEAD SEAL & LAMINATED STEEL CENTER

TUBE SEAL ORING

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

TRANSMISSION
Required: 3

TRANSMISSION
Required: 3

TRANSMISSION
Required: 3

PTO
Required: 3

USE WITH R50152

USE WITH R39259

FITS: HI-LOW SYNCRONIZER
Required: 8

USE WITH R29815
Required: QTY AS REQUIRED

FITS HI-LOW SYNCRONIZER
Required: 6

USE WITH R29816
Required: QTY AS REQUIRED

WITH BEAD SEAL & LAMINATED STEEL CENTER

WITH BEAD SEAL & LAMINATED STEEL CENTER

TUBE SEAL ORING

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

1 1/16" MALE O-RING x 7/8" MALE JIC

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

DIESEL INCLUDES: MOUNTING GASKET, NARROW GEAR TRAIN - GEAR #R71037
NOTE: PRIOR TO INSTALLATION POSITIVE GEAR TRAIN IDENTIFICATION MUST BE DONE.
THE NARROW STYLE GEAR USED ON R71224 HAS APPROX. 1/8" GAP BETWEEN TEETH AT THE TOOTH BASE.
THE WIDE STYLE GEAR USED ON R55986 HAS NO GAP AT THE TOOTH BASE AND HAS A NOTCH IN THE CENTER OF EACH TOOTH ON THE OD.

R934050 KIT AVAILABLE
CASTING #MARKED R71224, R83561

FITS: R71224 & R55986
INCLUDES: GASKETS, SEALS, O-RINGS, SNAP RING & BEARINGS

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

FOR INSTALLATION OF R22764 REAR MAIN SEAL

FOR INSTALLATION OF R22764 REAR MAIN SEAL

KIT INCLUDES: RESISTOR
REPLACES ORIGINAL ASSEMBLY, FOR REPLACEMENT MOTORS ORDER BM3904

12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE HEAVY DUTY BLOWER MOTOR WITH OE CONNECTORS BM20052HD

HD BEARING STYLE WITH OE WIRE CONNECTORS & O-RINGS, 12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
WITH OE WIRE CONNECTORS & MOUNTING O-RINGS
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE STANDARD VERSION BM20052

HIGH EFFICIENCY EVAPORATOR WITH HEATER CORE
MUST REUSE ORIGINAL BRACKETS

AFTERMARKET

NEW AP AIR DESIGN 6E171 COMPRESSOR WITH LATE DENSO 10PA17 INTERNAL DESIGN.
CAN RE-USE ORIGINAL MANIFOLD. FOR MANIFOLD REPLACEMENT KIT, ORDER 451-1173K.
CAN USE STANDARD DUTY DENSO STYLE - 503-116
CAN USE HD SANDEN STYLE COMPRESSOR - 503-117 WILL NOT FIT JOHN DEERE MODELS 2250, 2450, 2650, 2650N, 2850, 2355, 2555, 2755, 2855N, 2955, 3050, 3350, 3650, 3055, 3155, 3255 WITH JOHN DEERE AL63652 COMPRESSOR MOUNTING BRACKET.

CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.