Humboldt, Iowa

Dealers

Stay logged in

JOHN DEERE 4240 John Deere Models: 3005 thru 4995

12" PERMA CLUTCH

Top of Page

PERMA CLUTCH

THIS ASSEMBLY IS PRESET
INCLUDES: 2-R95827 ENGINE DISCS AND 2-R95827 PTO DISCS

  • CORE #:GR50156
  • CORE PRICE:$250.00*
  • SIZE:12"
  • LEVERS:6
  • SPRINGS:NONE
  • HUB/SPLINE:2 1/4" - 35 & 1 11/16" - 19
  • TYPE:DUAL STAGE

PERMA DISC

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

  • SIZE:12"
  • SPLINE:48 TEETH
  • TYPE:WET

CLUTCH HOUSING GASKET

S/N 007434 & BELOW (NORTH AMERICAN EDITION) & S/N 298640 & BELOW (EUROPEAN EDITION)

CLUTCH HOUSING GASKET

S/N 007435 & ABOVE (NORTH AMERICAN EDITION) & S/N 298641 & ABOVE (EUROPEAN EDITION)

ORING

TUBE SEAL ORING

12" PERMA CLUTCH COMPONENTS

Top of Page

PERMA DISC

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

  • SIZE:12"
  • SPLINE:48 TEETH
  • TYPE:WET

TRANSMISSION HUB

  • HUB:1 11/16"
  • SPLINE:19
  • TEETH:48

PTO HUB

  • HUB:2 1/4"
  • SPLINE:35
  • TEETH:48

ROCKER BOLT SPRING

TRANSMISSION
Required: 3

ROCKER

TRANSMISSION
Required: 3

ROCKER BOLT W/NUTS

TRANSMISSION
Required: 3

ADJ BOLT W/NUT

PTO
Required: 3

PTO LEVER

Required: 3

PTO PIN

Required: 3

13" CLUTCH POWERSHIFT

Top of Page

WOVEN DISC

  • CORE #:GR55655
  • CORE PRICE:$15.00
  • SIZE:13"
  • HUB:1 1/4"
  • SPLINE:19
  • CENTER:SPRING

6 REGULAR PAD DISC

  • CORE #:GR55655D
  • CORE PRICE:$15.00*
  • SIZE:13"
  • HUB:1 1/4"
  • SPLINE:19
  • CENTER:SPRING

STEEL PLATE

WITH SQUARE LUGS

  • SIZE:13 5/8"

RELEASE BEARING

GREASABLE

  • OD:3.500"
  • ID:2.062"
  • THICKNESS:.750"

RELEASE BEARING

NON-GREASABLE AETNA BEARING

  • OD:3.500"
  • ID:2.062"
  • THICKNESS:.750"

PILOT BEARING

  • OD:1.5748"
  • ID:.6693"
  • THICKNESS:.4724"

SPRING CUP

Required: 12 or 15

TRANSMISSION

SPRING

Required: 12

QUAD RANGE TRANSMISSION DISCS

Top of Page

FRICTION DISC

Required: QTY AS REQUIRED

USE WITH R50152

  • OD:7.760"
  • THICKNESS:0.090"
  • MAJOR SPLINE DIAMETER:6.700"
  • SPLINE COUNT:6

FRICTION DISC

REQUIRED: QTY AS REQUIRED

USE WITH R39259

  • OD:5.250"
  • THICKNESS:0.075"
  • MAJOR SPLINE DIAMETER:3.840"
  • SPLINE COUNT:45

FIBER DISC

FITS: HI-LOW SYNCRONIZER
Required: 8

  • OD:4.335"
  • # TEETH:55
  • THICKNESS:.070"

SEPARATOR PLATE

USE WITH R29815
Required: QTY AS REQUIRED

  • OD:7.760"
  • THICKNESS:0.090"

SEPARATOR PLATE

FITS HI-LOW SYNCRONIZER
Required: 6

  • MAJOR OD:4.700"
  • MINOR OD:4.335"
  • TEETH:6
  • THICKNESS:.046

SEPARATOR PLATE

USE WITH R29816
Required: QTY AS REQUIRED

  • OD:5.250"
  • THICKNESS:0.062"

POWER SHIFT TRANSMISSION DISCS

Top of Page

FRICTION DISCS

Required: QTY AS REQUIRED
  • OD:7.750"
  • THICKNESS:0.132"
  • MAJOR SPLINE DIAMETER:5.380"
  • SPLINE COUNT:42

SEPARATOR PLATE

Required: QTY AS REQUIRED
  • OD:7.750"
  • THICKNESS:0.120"

TRANSMISSION GASKETS AND SEALS

Top of Page

CLUTCH HOUSING GASKET

S/N 007434 & BELOW (NORTH AMERICAN EDITION) & S/N 298640 & BELOW (EUROPEAN EDITION)

CLUTCH HOUSING GASKET

S/N 007435 & ABOVE (NORTH AMERICAN EDITION) & S/N 298641 & ABOVE (EUROPEAN EDITION)

ORING

TUBE SEAL ORING

HYDRAULIC PUMP & PARTS

Top of Page

HYDRAULIC PUMP

WITHOUT POWER FRONT WHEEL DRIVE S/N 029865 AND BELOW

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON THE MOUNTING FLANGE LEFT SIDE , A 7/8" PRESSURE PORT IN THE PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON THE BOTTOM. IT DOES NOT HAVE AN INLET PORT ON THE MOUNTING FLANGE RIGHT SIDE.
NOTE: THE INDICATED SIDES OF PUMP ARE AS SEEN FROM THE TRACTOR SEAT.
IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED.

  • CORE #:GR56160
  • CORE PRICE:$150.00*

HYDRAULIC PUMP

WITHOUT POWER FRONT WHEEL DRIVE S/N 029866 AND ABOVE

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

  • CORE #:GR94660
  • CORE PRICE:$150.00*

HYDRAULIC PUMP

WITH POWER FRONT WHEEL DRIVE

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

  • CORE #:GR94661
  • CORE PRICE:$150.00*

HYDRAULIC PUMP

WITHOUT POWER FRONT WHEEL DRIVE S/N 029866 AND ABOVE

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

  • CORE #:GR94660
  • CORE PRICE:$150.00*

JD HYDRAULIC PUMP FITTING

1 1/16" MALE O-RING x 7/8" MALE JIC

JD HYDRAULIC PUMP FITTING

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

HYDRAULIC PUMP CAMSHAFT KIT

FITS: 4 C.I. (65cc) PUMPS WITH SERIAL PLATE
INCLUDES: CAMSHAFT, CAM BUSHING & ROLLERS, SHAFT BEARINGS & THRUST WASHERS

HYDRAULIC PUMP BUSHING W/ROLLERS

USE WITH R79152, R79154 & R79156 SHAFTS

HYDRAULIC PUMP BUSHING

USE WITH R79152, R79154 & R79156 SHAFTS

HYDRAULIC PUMP BUSHING

USE WITH R34348 SHAFT

HYDRAULIC PUMP THRUST WASHER

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

HYDRAULIC PUMP THRUST WASHER

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

HYDRAULIC PUMP BEARING

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

HYDRAULIC PUMP

WITH POWER FRONT WHEEL DRIVE

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

  • CORE #:GR94661
  • CORE PRICE:$150.00*

WATER PUMP

Top of Page

WATER PUMP

DIESEL
INCLUDES: HUB, BACKPLATE, BACKPLATE GASKET AND MOUNTING GASKET
R938430 KIT AVAILABLE

  • CORE #:GR61439
  • CORE PRICE:$75.00
  • CASTING #:R61439

WATER PUMP REPAIR KIT

FITS: R61439
INCLUDES: 2 GASKETS, SPRING SEAL & BEARING

WATER PUMP

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

BRAKES

Top of Page

RIVET

Required: 2 OR 3 SETS FOR BOTH WHEELS

3/16" X 31/64"-18 PER SET

RIVET

Required: 1 SET FOR BOTH WHEELS

3/16" X 43/64"- 18 PER SET

TOOLS

Top of Page

REAR MAIN SEAL INSTALLATION TOOL

FOR INSTALLATION OF R22764 REAR MAIN SEAL

AIR CONDITIONING

Top of Page

CONVERSION KIT

EURO

A6 TO ALTERNATIVE SANDEN CONVERSION KIT
REPLACES ORIGINAL A6 COMPRESSOR
KIT INCLUDES: 990-403 CONVERSION KIT, RECEIVER DRIER, EXPANSION VALVE & O-RINGS.
KIT ALLOWS FOR THE USE OF THE ORIGINAL BELT AND HOSES.
CAN USE COMPLETE CONVERSION KIT WITH OE SANDEN COMPRESSOR 990-404K.

  • COMPRESSOR:509-5713
  • MOUNTING BRACKET:995-430
  • MOUNTING HARDWARE:YES
  • BELT:NO
  • BINARY SWITCHES:220-207, 220-3085, 110-0802
  • COMPRESSOR MANIFOLD:451-11602
  • SERVICE VALVES:NO
  • RETROFIT ADAPTERS:461-3098, 461-3099
  • HOSES:NO
  • RECEIVER DRIER:804-5501
  • O-RINGS:530-4093

BLOWER MOTOR

EURO

UPDATE KIT

  • OEM #:AR74019, AR49968
  • TYPE:SINGLE SPEED
  • OVERALL HEIGHT:4 3/4"
  • OVERALL WIDTH:5 3/4"
  • VOLTAGE:12
  • MOUNTING BASE LENGTH:14 3/4"
  • MOUNTING BASE WIDTH:5"

BLOWER MOTOR

KIT INCLUDES: RESISTOR
REPLACES ORIGINAL ASSEMBLY, FOR REPLACEMENT MOTORS ORDER BM3904

  • TYPE:COMPLETE ASSEMBLY
  • OVERALL HEIGHT:5 3/4"
  • OVERALL WIDTH:7"
  • VOLTAGE:12
  • MOUNTING BASE LENGTH:21"
  • MOUNTING BASE WIDTH:6 5/8"

CAB FILTER

  • OEM #:RE12793
  • OVERALL LENGTH:28"
  • OVERALL WIDTH:7 1/2"
  • OVERALL THICKNESS:2 3/4"

HD BLOWER MOTOR

EURO

HEAVY DUTY BEARING STYLE WITH OE WIRE CONNECTORS 12V SINGLE SPEED 2 WIRE WITH 5/16" SHAFTS

OE WIRE CONNECTORS
SEALED MOTOR

  • TYPE:DOUBLE SHAFT, SINGLE SPEED
  • SHAFT SIZE:5/16"
  • SHAFT LENGTH:2 3/4"
  • MOTOR DIAMETER:3"
  • MOTOR LENGTH:3 3/4"
  • OVERALL LENGTH:10"
  • ROTATION:REVERSIBLE
  • NUMBER OF WIRES:2
  • VOLTAGE:12
  • STUD SPAN:2 5/16"

BLOWER MOTOR

12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE HEAVY DUTY BLOWER MOTOR WITH OE CONNECTORS BM20052HD

  • OEM #:AR82005, RE251028, RE13882
  • TYPE:DOUBLE SHAFT, SINGLE SPEED
  • SHAFT SIZE:3/8"
  • SHAFT LENGTH:5"
  • MOTOR DIAMETER:3 1/4"
  • MOTOR LENGTH:4 1/8"
  • OVERALL LENGTH:14 3/4"
  • ROTATION:REVERSIBLE
  • NUMBER OF WIRES:2
  • VOLTAGE:12
  • STUD SPAN:2 1/2"

BLOWER MOTOR

HD BEARING STYLE WITH OE WIRE CONNECTORS & O-RINGS, 12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
WITH OE WIRE CONNECTORS & MOUNTING O-RINGS
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE STANDARD VERSION BM20052

  • OEM #:AN276546, RE10999, RE25160, AT74427
  • TYPE:DOUBLE SHAFT, SINGLE SPEED
  • SHAFT SIZE:3/8"
  • SHAFT LENGTH:5"
  • MOTOR DIAMETER:3 1/4"
  • MOTOR LENGTH:4 1/8"
  • OVERALL LENGTH:14 3/4"
  • ROTATION:REVERSIBLE
  • NUMBER OF WIRES:2
  • VOLTAGE:12
  • STUD SPAN:2 1/2"

CONDENSER W/OIL COOLER

EURO

ORIGINAL EQUIPMENT DESIGNED CONDENSER WITH OIL COOLER - AR96767;
CAN UPGRADE TO HIGH EFFICIENCY VERSION - 400-5581

  • OEM #:AR96767, AR80127, AR81926
  • OVERALL HEIGHT:24 1/2"
  • OVERALL WIDTH:22 1/4"
  • CORE HEIGHT:20 1/2"
  • CORE WIDTH:22"
  • CORE THICKNESS:2 1/2"
  • FITTING INLET:#8 MALE O-RING
  • FITTING OUTLET:#6 MALE O-RING
  • NUMBER OF ROWS:4
  • SWITCH PORT:N/A
  • OIL COOLER:OIL COOLER

EVAPORATOR/HEATER CORE

HIGH EFFICIENCY EVAPORATOR WITH HEATER CORE
MUST REUSE ORIGINAL BRACKETS

  • OEM #:AZ37729, RE2265, AR88076, AR85245, AG331433
  • VALVE TYPE:BULB TYPE
  • FITTING TYPE:O-RING
  • OVERALL LENGTH:33 1/4"
  • OVERALL HEIGHT:5"
  • OVERALL WIDTH:12 1/2"
  • CORE HEIGHT:5"
  • CORE WIDTH:3 1/8"
  • CORE LENGTH:29"
  • FITTING INLET:#8 FEMALE O-RING
  • FITTING OUTLET:#10 FEMALE O-RING

BULB W/9" CAPILLARY TUBE

OE BULB TYPE, EXTERNALLY EQUALIZED 9" CAPPILLARY TUBE R12 & R134a COMPATIBLE

  • OEM #:AT60277, AH204686, AH140818, RE206757, AL28638, WR51414
  • BULB TYPE:1/2" BULB
  • EQUALIZER TUBE LENGTH:9"
  • CAPILLARY TUBE LENGTH:9"
  • TYPE:O-RING
  • LIQUID INLET:#6, 3/8" MALE O-RING
  • LIQUID INLET TO EVAPORATOR:#8, 1/2" MALE O-RING
  • TONAGE:1 1/2"
  • EQUALIZER TYPE:1/4" FEMALE O-RING

14" CAPILLARY TUBE

Euro

AFTERMARKET

  • OEM #:2G-0401, 3E-9343, 1280333C2, AH204686, RE206757, 3321511M91
  • BULB TYPE:3/8" COIL
  • EQUALIZER TUBE LENGTH:16"
  • TYPE:O-RING
  • LIQUID INLET:#6, 3/8" O-RING
  • LIQUID OUTLET:#8, 1/2" MALE O-RING
  • TONAGE:1 1/2"
  • EQUALIZER TYPE:1/4" FEMALE O-RING
  • CAPILLARY TUBE LENGTH:14"

CONVERSION KIT

EURO

REPLACES ORIGINAL A6 COMPRESSOR
INCLUDES: 990-404 SANDEN CONVERSION KIT, RECEIVER DRIER, EXPANSION VALVE & O-RINGS.
KIT ALLOWS FOR THE USE OF THE ORIGINAL BELT AND HOSES.
CAN USE COMPLETE CONVERISON KIT WITH AFTERMARKET SANDEN COMPRESSOR 990-403K.

  • COMPRESSOR:509-571
  • MOUNTING BRACKET:995-430
  • BELT:NO
  • BINARY SWITCHES:220-207, 220-3085, 110-0802
  • COMPRESSOR MANIFOLD:451-11602
  • SERVICE VALVES:NO
  • RETROFIT ADAPTERS:461-3098, 461-3099
  • HOSES:NO
  • O-RINGS:530-4093

HEATER CONTROL VALVE

EURO
  • OEM #:AR89913, AR100056, AR70418

O-RING KIT

EURO

FITS ALL 30 & 40 SERIES JOHN DEERE TRACTORS,
27 PIECE KIT,
SINGLE APPLICATION

RECEIVER DRIER

CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.

  • OEM #:295006A1, AR74486, 87105840, AH234098, AR59780, RE214439, 87280717, RE576834
  • DIAMETER:4"
  • OVERALL HEIGHT:7.5"
  • FITTING INLET:#6 FEMALE O-RING
  • FITTING OUTLET:#6 MALE O-RING
  • SIGHT GLASS:2, SIGHT GLASSES
AG PARTS ONLINE
AP Air, INC.
AP Truck Parts
DKC_SOLUTIONS
ROMAINE ELECTRIC
Spencer Diesel

Shopping Cart Update Cart ()

Loading...