JOHN DEERE 4320 John Deere Models: 3005 thru 4995

INCLUDES: PPA, WOVEN ENGINE DISC, RELEASE & PILOT BEARINGS
FLYWHEEL STEP: 2.964"

INCLUDES: PPA, WOVEN PTO DISC, NEW DESIGN, SMOOTH ENGAGING 6 PAD ENGINE DISC, RELEASE & PILOT BEARINGS
FLYWHEEL STEP: 2.964"

INCLUDES: PPA, 6 PAD PTO DISC, NEW DESIGN, SMOOTH ENGAGING 6 PAD ENGINE DISC, RELEASE & PILOT BEARINGS
FLYWHEEL STEP: 2.964"

INCLUDES: PPA, 6 PAD PTO DISC, NEW DESIGN, SMOOTH ENGAGING 6 PAD ENGINE DISC, AETNA RELEASE BEARING & PILOT BEARING
FLYWHEEL STEP: 2.964"

INCLUDES: R26688 PTO DISC
FLYWHEEL STEP: 2.964"
(NEW AVAILABLE)

INCLUDES: R26688 PTO DISC
FLYWHEEL STEP: 2.964"

INCLUDES: R26688 HD6 PTO DISC
FLYWHEEL STEP: 2.964"

(NEW AVAILABLE)

NEW DESIGN, SMOOTH ENGAGING, LESS ABRASIVE OFFSET PADS

GREASABLE

NON-GREASABLE AETNA BEARING

GREASABLE

INCLUDES: RING GEAR

(NEW AVAILABLE)

(NEW AVAILABLE)

(NEW AVAILABLE)

INCLUDES: 3 TRANSMISSION LEVERS, PINS AND ANTI-RATTLE SPRINGS AND 3 PTO LEVERS AND PINS

TRANSMISSION INNER PRESSURE SPRING
Required: 15

PTO PLATE RETURN SPRING

TRANSMISSION LEVER SPRING

TRANSMISSION

TRANSMISSION

TRANSMISSION
Required: 3

7/16" 20 THREAD
Required: 3

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON THE MOUNTING FLANGE LEFT SIDE , A 7/8" PRESSURE PORT IN THE PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON THE BOTTOM. IT DOES NOT HAVE AN INLET PORT ON THE MOUNTING FLANGE RIGHT SIDE.
NOTE: THE INDICATED SIDES OF PUMP ARE AS SEEN FROM THE TRACTOR SEAT.
IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED.

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

1 1/16" MALE O-RING x 7/8" MALE JIC

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

FITS: 4 C.I. (65cc) PUMPS WITH SERIAL PLATE
INCLUDES: CAMSHAFT, CAM BUSHING & ROLLERS, SHAFT BEARINGS & THRUST WASHERS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R34348 SHAFT

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

INCLUDES: BACKPLATE GASKET & MOUNTING GASKET
R937020 KIT AVAILABLE

FITS: R46561 & R43114
INCLUDES: 2 GASKETS, SPRING SEAL & BEARING

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

FOR INSTALLATION OF R22764 REAR MAIN SEAL

3/16" X 31/64"-18 PER SET

3/16" X 43/64"- 18 PER SET

FOR INSTALLATION OF R22764 REAR MAIN SEAL

UPDATE KIT

HEAVY DUTY BEARING STYLE WITH OE WIRE CONNECTORS 12V SINGLE SPEED 2 WIRE WITH 5/16" SHAFTS

OE WIRE CONNECTORS
SEALED MOTOR