JOHN DEERE 4440 John Deere Models: 3005 thru 4995

THIS ASSEMBLY IS PRESET
INCLUDES: 2-R95827 ENGINE DISCS AND 2-R95827 PTO DISCS

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

TUBE SEAL ORING

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

TRANSMISSION
Required: 3

TRANSMISSION
Required: 3

TRANSMISSION
Required: 3

PTO
Required: 3

WITH SQUARE LUGS

TRANSMISSION

USE WITH R50152

USE WITH R39259

FITS: HI-LOW SYNCRONIZER
Required: 8

USE WITH R29815
Required: QTY AS REQUIRED

FITS HI-LOW SYNCRONIZER
Required: 6

USE WITH R29816
Required: QTY AS REQUIRED

TUBE SEAL ORING

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON THE MOUNTING FLANGE LEFT SIDE , A 7/8" PRESSURE PORT IN THE PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON THE BOTTOM. IT DOES NOT HAVE AN INLET PORT ON THE MOUNTING FLANGE RIGHT SIDE.
NOTE: THE INDICATED SIDES OF PUMP ARE AS SEEN FROM THE TRACTOR SEAT.
IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED.

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

1 1/16" MALE O-RING x 7/8" MALE JIC

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

FITS: 4 C.I. (65cc) PUMPS WITH SERIAL PLATE
INCLUDES: CAMSHAFT, CAM BUSHING & ROLLERS, SHAFT BEARINGS & THRUST WASHERS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R34348 SHAFT

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

DIESEL
INCLUDES: HUB, BACKPLATE, BACKPLATE GASKET AND MOUNTING GASKET
R938430 KIT AVAILABLE

FITS: R61439
INCLUDES: 2 GASKETS, SPRING SEAL & BEARING

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

FOR INSTALLATION OF R22764 REAR MAIN SEAL

3/16" X 31/64"-18 PER SET

3/16" X 43/64"- 18 PER SET

FOR INSTALLATION OF R22764 REAR MAIN SEAL

A6 TO ALTERNATIVE SANDEN CONVERSION KIT
REPLACES ORIGINAL A6 COMPRESSOR
KIT INCLUDES: 990-403 CONVERSION KIT, RECEIVER DRIER, EXPANSION VALVE & O-RINGS.
KIT ALLOWS FOR THE USE OF THE ORIGINAL BELT AND HOSES.
CAN USE COMPLETE CONVERSION KIT WITH OE SANDEN COMPRESSOR 990-404K.

UPDATE KIT

KIT INCLUDES: RESISTOR
REPLACES ORIGINAL ASSEMBLY, FOR REPLACEMENT MOTORS ORDER BM3904

HEAVY DUTY BEARING STYLE WITH OE WIRE CONNECTORS 12V SINGLE SPEED 2 WIRE WITH 5/16" SHAFTS

OE WIRE CONNECTORS
SEALED MOTOR

12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE HEAVY DUTY BLOWER MOTOR WITH OE CONNECTORS BM20052HD

HD BEARING STYLE WITH OE WIRE CONNECTORS & O-RINGS, 12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
WITH OE WIRE CONNECTORS & MOUNTING O-RINGS
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE STANDARD VERSION BM20052

ORIGINAL EQUIPMENT DESIGNED CONDENSER WITH OIL COOLER - AR96767;
CAN UPGRADE TO HIGH EFFICIENCY VERSION - 400-5581

HIGH EFFICIENCY EVAPORATOR WITH HEATER CORE
MUST REUSE ORIGINAL BRACKETS

OE BULB TYPE, EXTERNALLY EQUALIZED 9" CAPPILLARY TUBE R12 & R134a COMPATIBLE

AFTERMARKET

REPLACES ORIGINAL A6 COMPRESSOR
INCLUDES: 990-404 SANDEN CONVERSION KIT, RECEIVER DRIER, EXPANSION VALVE & O-RINGS.
KIT ALLOWS FOR THE USE OF THE ORIGINAL BELT AND HOSES.
CAN USE COMPLETE CONVERISON KIT WITH AFTERMARKET SANDEN COMPRESSOR 990-403K.

FITS ALL 30 & 40 SERIES JOHN DEERE TRACTORS,
27 PIECE KIT,
SINGLE APPLICATION

CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.