INCLUDES: 4 - R95827 ENGINE DISCS & 3 - R95827 PTO DISCS
CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED
WITH BEAD SEAL & LAMINATED STEEL CENTER
TUBE SEAL ORING
TRANSMISSION Required: 3
PTO Required: 3
USE WITH R50152
USE WITH R39259
USE WITH R29815 Required: QTY AS REQUIRED
USE WITH R29816 Required: QTY AS REQUIRED
THIS IS A 65 CM (4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT
USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R34348 SHAFT
USE WITH R79152, R79154, R79156 & R34348 SHAFTS Required: 2
ONLY USED WITH POWER SHIFT TRANSMISSION
DIESEL INCLUDES: MOUNTING GASKET, NARROW GEAR TRAIN - GEAR #R71037 NOTE: PRIOR TO INSTALLATION POSITIVE GEAR TRAIN IDENTIFICATION MUST BE DONE. THE NARROW STYLE GEAR USED ON R71224 HAS APPROX. 1/8" GAP BETWEEN TEETH AT THE TOOTH BASE. THE WIDE STYLE GEAR USED ON R55986 HAS NO GAP AT THE TOOTH BASE AND HAS A NOTCH IN THE CENTER OF EACH TOOTH ON THE OD.
R934050 KIT AVAILABLE CASTING #MARKED R71224, R83561
FITS: R71224 & R55986 INCLUDES: GASKETS, SEALS, O-RINGS, SNAP RING & BEARINGS
SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS
FOR INSTALLATION OF R22764 REAR MAIN SEAL
KIT INCLUDES: RESISTOR REPLACES ORIGINAL ASSEMBLY, FOR REPLACEMENT MOTORS ORDER BM3904
12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS. REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR. CAN USE HEAVY DUTY BLOWER MOTOR WITH OE CONNECTORS BM20052HD
HD BEARING STYLE WITH OE WIRE CONNECTORS & O-RINGS, 12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS. WITH OE WIRE CONNECTORS & MOUNTING O-RINGS REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR. CAN USE STANDARD VERSION BM20052
HIGH EFFICIENCY EVAPORATOR WITH HEATER CORE MUST REUSE ORIGINAL BRACKETS
AFTERMARKET
NEW AP AIR DESIGN 6E171 COMPRESSOR WITH LATE DENSO 10PA17 INTERNAL DESIGN. CAN RE-USE ORIGINAL MANIFOLD. FOR MANIFOLD REPLACEMENT KIT, ORDER 451-1173K. CAN USE STANDARD DUTY DENSO STYLE - 503-116 CAN USE HD SANDEN STYLE COMPRESSOR - 503-117 WILL NOT FIT JOHN DEERE MODELS 2250, 2450, 2650, 2650N, 2850, 2355, 2555, 2755, 2855N, 2955, 3050, 3350, 3650, 3055, 3155, 3255 WITH JOHN DEERE AL63652 COMPRESSOR MOUNTING BRACKET.
CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.