JOHN DEERE 5010 John Deere Models: 5010 thru 6930

ROUND HOLE TRANSMISSION CAST
FLYWHEEL STEP: 3.207" - 3.217"

SQUARE SLOT TRANSMISSION CAST
FLYWHEEL STEP: 3.207" - 3.217"

Required: 2

Required: 2

HAS ROUND DRIVE PIN HOLES

SQUARE SLOTS
HAS SLOTTED DRIVE PIN HOLES

TRANSMISSION INNER PRESSURE SPRING
Required: 12

TRANSMISSION OUTER PRESSURE SPRING

(R97872 NEW AVAILABLE);
THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM. NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

THIS IS A 50 CM (3 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON THE MOUNTING FLANGE LEFT SIDE , A 7/8" PRESSURE PORT IN THE PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON THE BOTTOM. IT DOES NOT HAVE AN INLET PORT ON THE MOUNTING FLANGE RIGHT SIDE.
NOTE: THE INDICATED SIDES OF PUMP ARE AS SEEN FROM THE TRACTOR SEAT.
IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED.

THIS IS A 40 CM (2.4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 5/8" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

1 1/16" MALE O-RING x 7/8" MALE JIC

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R34348 SHAFT

USE WITH R34348 SHAFT AND
USE WITH R45874B & R45874BR BUSHINGS
Required: 2

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

DIESEL
INCLUDES: MOUNTING GASKET & BACKPLATE GASKET

FITS: R36812
INCLUDES: 2 GASKETS, SPRING SEAL & BEARING

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

3/16" X 31/64"-18 PER SET

3/16" X 43/64"- 18 PER SET

3/16" x 1 1/2" - 18 PER SET
Required: 1 SET PER WHEEL