JOHN DEERE 8430 John Deere Models: 7020 thru 9970

COMPLETE PRESET CLUTCH ASSEMBLY INCLUDES: 4 - R95827 DISCS

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

TUBE SEAL ORING

CAN BE USED AS A PTO OR AN ENGINE DISC REPLACEMENT DISC FOR REBUILDING PERMA CLUTCH PRESSURE PLATE ASSEMBLY Required: AS REQUIRED

TRANSMISSION
Required: 3

TRANSMISSION
Required: 3

USE WITH R50152

USE WITH R39259

USE WITH R29815
Required: QTY AS REQUIRED

USE WITH R29816
Required: QTY AS REQUIRED

TUBE SEAL ORING

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

1 1/16" MALE O-RING x 7/8" MALE JIC

45 DEGREE HYDRAULIC PUMP FITTING 1 1/16" MALE O-RING x 7/8" MALE JIC

FITS: 4 C.I. (65cc) PUMPS WITH SERIAL PLATE
INCLUDES: CAMSHAFT, CAM BUSHING & ROLLERS, SHAFT BEARINGS & THRUST WASHERS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS

USE WITH R79152, R79154 & R79156 SHAFTS
USE WITH R80558B & R80558BR BUSHINGS
Required: 2

USE WITH R79152, R79154, R79156 & R34348 SHAFTS
Required: 2

THIS IS A 65 CM (4 CI) HYDRAULIC PUMP
THIS PUMP HAS A 1 1/16" INLET PORT ON MOUNTING FLANGE LEFT SIDE , A 1 1/16" INLET PORT ON MOUNTING FLANGE RIGHT SIDE, A 1 1/16" PRESSURE PORT IN PUMP BODY ON RIGHT SIDE, A 7/8" COOLER RETURN PORT ON TOP AND A 3/8" DRAIN PORT ON BOTTOM.
NOTE: IF YOUR APPLICATION DOES NOT HAVE A DRAIN LINE THE INSTALLATION OF J D PART AR39810 DRAIN LINE KIT IS REQUIRED
THE INDICATED SIDES OF THE PUMP ARE AS SEEN FROM THE TRACTOR SEAT

INCLUDES: MOUNTING GASKET
R934040 KIT AVAILABLE

FITS: R51683 & R58713
INCLUDES: 3 GASKETS, SPRING SEAL & BEARING

SEAL INSTALLER FOR THE INSTALLATION OF UNITIZED WATER PUMP SEALS

GEAR DRIVEN W/14 TOOTH GEAR;
INCLUDES: INSTALLATION TOOL, O-RINGS & SNAP RING
DOES NOT INCLUDE: COVER GASKET

FOR INSTALLATION OF R22764 REAR MAIN SEAL

3/16" X 31/64"-18 PER SET

FOR INSTALLATION OF R22764 REAR MAIN SEAL

A6 TO ALTERNATIVE SANDEN CONVERSION KIT
REPLACES ORIGINAL A6 COMPRESSOR
KIT INCLUDES: 990-403 CONVERSION KIT, RECEIVER DRIER, EXPANSION VALVE & O-RINGS.
KIT ALLOWS FOR THE USE OF THE ORIGINAL BELT AND HOSES.
CAN USE COMPLETE CONVERSION KIT WITH OE SANDEN COMPRESSOR 990-404K.

UPDATE KIT

HEAVY DUTY BEARING STYLE WITH OE WIRE CONNECTORS 12V SINGLE SPEED 2 WIRE WITH 5/16" SHAFTS

OE WIRE CONNECTORS
SEALED MOTOR

12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE HEAVY DUTY BLOWER MOTOR WITH OE CONNECTORS BM20052HD

HD BEARING STYLE WITH OE WIRE CONNECTORS & O-RINGS, 12 VOLT SINGLE SPEED 2 WIRE MOTOR WITH 3/8" SHAFTS.
WITH OE WIRE CONNECTORS & MOUNTING O-RINGS
REPLACES BUSHING STYLE MOTOR WITH NEW HD BEARING STYLE MOTOR.
CAN USE STANDARD VERSION BM20052

HIGH EFFICIENCY EVAPORATOR WITH HEATER CORE
MUST REUSE ORIGINAL BRACKETS

AFTERMARKET

REPLACES ORIGINAL A6 COMPRESSOR
INCLUDES: 990-404 SANDEN CONVERSION KIT, RECEIVER DRIER, EXPANSION VALVE & O-RINGS.
KIT ALLOWS FOR THE USE OF THE ORIGINAL BELT AND HOSES.
CAN USE COMPLETE CONVERISON KIT WITH AFTERMARKET SANDEN COMPRESSOR 990-403K.

FITS ALL 30 & 40 SERIES JOHN DEERE TRACTORS,
27 PIECE KIT,
SINGLE APPLICATION

CAN USE ORIGINAL JD VERSION 804-5502. CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.