CASE-IH 7120 Case-IH Models: 4210 thru 9390

REMAN WITH 6 MOUNTING HOLES

WITH 6 MOUNTING HOLES

INPUT SHAFT;
INCLUDES: 20 - 86990276 FRICTION DISCS, 18 - 92934 SEPARATOR PLATES, SEALS & O-RINGS

COUNTERSHAFT;
INCLUDES: 15 - 86990276 FRICTION DISCS, 14 - 92934 SEPARATOR PLATES, 1-87738316 SEPARATOR PLATE, SEALS & O-RINGS

RANGE TRANSMISSION MASTER CLUTCH;
INCLUDES: 9 - 1285975C1 FRICTION DISCS, 9 - 1285974C1 SEPARATOR PLATES, SEALS & O-RINGS

INCLUDES: GASKET, O-RING & SEAL KIT

INCLUDES: GASKET, O-RING & SEAL KIT

INCLUDES: GASKET, O-RING & SEAL KIT

INPUT SHAFT

COUNTER SHAFT

INPUT SHAFT W/O CREEPER;
INCLUDES: 14-86990276 FRICTION DISCS, 14-92934 SEPARATOR PLATES & O-RINGS

INPUT SHAFT W/CREEPER;
INCLUDES: 14-86990276 FRICTION DISCS, 14-92934 SEPARATOR PLATES & O-RINGS;
TRANSMISSION S/N ANJ0055132 & BELOW

INPUT SHAFT W/CREEPER;
INCLUDES: 14-86990276 FRICTION DISCS, 12-92934 SEPARATOR PLATES & O-RINGS

COUNTERSHAFT W/ CREEPER;
INCLUDES: 8-86990276 FRICTION DISCS, 7-92934 SEPARATOR PLATES & O-RINGS

OUTPUT SHAFT FRONT CLUTCH;
INCLUDES: 14-86990276 FRICTION DISCS, 12-92934 SEPARATOR PLATES & O-RINGS

OUTPUT SHAFT REAR CLUTCH;
INCLUDES: 18-86990276 FRICTION DISCS, 16-92934 SEPARATOR PLATES & O-RINGS

INPUT SHAFT

INPUT SHAFT W/CREEPER

INPUT SHAFT W/O CREEPER

OUTPUT SHAFT

CONTROL VALVE MOUNTING PLATE TO CLUTCH HOUSING GASKET

CONTROL VALVE BODY TO MOUNTING PLATE GASKET

CONTROL VALVE BODY TO BODY PLATE GASKET

CONTROL VALVE BODY TO BODY PLATE GASKET

CONTROL VALVE BODY TO CAM HOUSING GASKET

CLUTCH CONTROL VALVE STEM HOUSING GASKET

CREEPER VALVE / LOWER PLATE HOUSING GASKET

FORWARD / REVERSE SPOOL HOUSING

SMALL OUTER COVER PLATE GASKET ON CAM HOUSING

LARGE OUTSIDE COVER PLATE GASKET ON CAM HOUSING

SHIFT / CAM SHAFT SEAL

FWD/REV SPOOL

CLUTCH CONTROL VALVE STEM

BODY PLATE TO MOUNTING PLATE

REPAIR SLEEVE
FITS OVER ORIGINAL AXLE SLEEVE, REQUIRES USE OF 1349183C1 OVERSIZED SEAL
FITS TRACTORS WITH 4" AXLES

OVERSIZED AXLE SEAL, USE WITH 1349184C1 REPAIR SLEEVE
FITS TRACTORS WITH 4" AXLES

ORIGINAL AXLE SEAL SLEEVE
REQUIRES THE USE OF 1963839C1 SEAL
FITS TRACTORS WITH 4" AXLES

ORIGINAL SIZE SEAL
USE WITH ORIGINAL AXLE SEAL SLEEVE 1963837C1
FITS TRACTORS WITH 4" AXLES

CONVERTS 1000 RPM SINGLE SPEED UNIT TO DUAL SPEED 1000 AND 540 RPM

KIT CONTENTS:
77724 PTO GASKET KIT
381489 SEPARATOR PLATE (11)
381490 FIBER DISC (10)
67340 BRAKE PISTON (3)

KIT CONTENTS:
77724 PTO GASKET KIT
381489 SEPARATOR PLATE (11)
381490 HD FIBER DISC (10)
67340 BRAKE PISTON (3)

KIT CONTENTS:
77724 PTO GASKET KIT
381489 SEPARATOR PLATE (11)
381490 FIBER DISC (10)

KIT CONTENTS:
77724 PTO GASKET KIT
381489 SEPARATOR PLATE (11)
381490 HD FIBER DISC (10)

FITS: 1259531 VALVE HOUSING

CONTAINS: 9 STEEL PLATES & 8 FIBER PLATES

CONTAINS: 9 STEEL PLATES & 8 FIBER PLATES
HEAVY DUTY OPTION FOR 68804

KIT INCLUDES: 11-381489 SEP PLATES AND 10-381490 DISCS

KIT INCLUDES: 11-381489 SEP PLATES AND 10-381490 HD DISCS

CONTAINS: 10 INTERNAL TOOTH & 10 EXTERNAL TOOTH FRICTION PLATES

USE FOR 1349453C1 & 139281C3

FOR PTO HOUSING S/N 35684 & BELOW
1000 RPM, 1 3/8" - 21 SPLINE OUTPUT SHAFT
THIS SHAFT HAS A STANDARD LENGTH REAR BEARING SURFACE AND DOES NOT REQUIRE THE USE OF A SPACER

FOR PTO HOUSING S/N 35685 & ABOVE
1000 RPM, 1 3/8" - 21 SPLINE OUTPUT SHAFT
THIS SHAFT HAS AN EXTENDED LENGTH REAR BEARING SURFACE(1.100 BEARING STOP TO SNAP RING GROOVE) AND REQUIRES THE USE OF SPACER P/N 1349266

SPACER FOR USE ON 1349263 PTO SHAFT

FOR 1000 RPM SHAFT

FOR 540 RPM SHAFT

BEARING RETAINING RING

540 SHAFT DRIVEN GEAR - DUAL SPEED ONLY

SPACER FOR 540 SHAFT DRIVEN GEAR - DUAL SPEED ONLY

PTO IDLER SHAFT - DUAL SPEED ONLY

IDLER GEAR THRUST WASHER - DUAL SPEED ONLY - 2 REQUIRED

IDLER GEAR BEARING - DUAL SPEED PTO ONLY - 2 REQUIRED

540 OUTPUT SHAFT FRONT BEARING - DUAL SPEED ONLY

(NEW AVAILABLE)
Required: 3

FITS: 540 RPM AND 1 3/8" 1000 RPM SHAFTS
2 REQUIRED

540 OUTPUT SHAFT

SPIRAL SHAFT SEAL RETAINING RING FOR 540 OUTPUT SHAFT

TEFLON CLUTCH DRUM SEAL RING

CAST CLUTCH DRUM SEAL RING
HD OPTION FOR 381485

CLUTCH DRUM TO SHAFT O-RING

CLUTCH PISTON INNER O-RING

CLUTCH CARRIER PRESSURE PORT SEAL

TEFLON CLUTCH SHAFT LUBE SEAL RING

PTO CLUTCH FRICTION DISC
Required: 10-ALL SINGLE SPEED AND DUAL SPEED PIN JJA0020936 & BELOW; 8-DUAL SPEED PIN JJA002937 & ABOVE

HD OPTION FOR 381490
Required: 10 - FOR ALL SINGLE SPEED PTO'S
AND FOR DUAL SPEED PTO'S PIN JJA0020936 & BELOW
8 - FOR DUAL SPEED PTO'S PIN JJA0020937 & ABOVE

51 INTERNAL TEETH WITH FRICTION MATERIAL ON 1 SIDE
CAN ONLY BE USED WITH 1863971

6 EXTERNAL TABS WITH FRICTION MATERIAL ON 1 SIDE
CAN ONLY BE USED WITH 1863972

ELIMINATES DRAFT SENSING COMPUTER, BUT WILL NOT DETECT DEFECTIVE PINS

ALLOWS TRACTOR TO HAVE FULL DRAFT SENSING IF ONLY 1 PIN IS WORKING

INCLUDES: PULLEY AND MOUNTING O-RING
(NEW AVIALABLE)

INCLUDES: PULLEY AND MOUNTING O-RING

FOR INSTALLATION OF A77810 REAR MAIN SEAL 5.9 & 8.3 CUMMINS ENGINE

INCLUDES: 3-120486 SEPARATOR PLATES, 3-120488 BRAKE DISCS, 1-139189 RETURN PLATE
Required: 1 PER SIDE

W/MECHANICAL FRONT WHEEL DRIVE
Required: 1 PER SIDE

SEALS ONLY, DOES NOT CONTAIN BUSHING\
Required: 1 PER SIDE

STEERING CLYINDER UPGRADE KIT
FITS: MFD TRACTORS WITH ORIGINAL CYLINDERS

FITS: ORIGINAL MFD STEERING CYLINDERS THAT HAVE NOT HAD UPGRADED CYL KIT INSTALLED

INCLUDES: 10 BOLT HUB SEAL, SUNSHAFT SEAL & BUSHING KIT

FOR INSTALLATION OF A77810 REAR MAIN SEAL 5.9 & 8.3 CUMMINS ENGINE

CAN ORDER 6 PACK - 320-143481-6

INCLUDES: EARLY & LATE STYLE WIRING HARNESS AND RESISTOR;
CAN USE OE BLOWER ASSEMBLY - BM4020K

5/8" HOSE MANUAL ON/OFF HEATER HOSE VALVE WITH 3/8" MALE PIPE THREAD;
FOR 5/8" HOSE

INCLUDES: OE SNADEN COMPRESSOR, RECEIVER DRIER, EXPANSION VALVE & O-RINGS
CAN USE ALTERNATIVE SANDEN KIT - 890-56013

CAN USE OE SANDEN COMPRESSOR - 509-603

4" X 7 3/4" MALE AND FEMALE O-RING, FRONT MOUNT.
CAN USE HEAVY DUTY DRY-TECH SERIES 804-545.

CAN USE ORIGINAL JD VERSION 804-5502.
CAN USE HEAVY DUTY DRY-TECH VERSION 804-550.

CAN USE OE SANDEN COMPRESSOR - 509-560